Describe your furnace job, and a local pro who handles it gets in touch.
You want a straight number before you call anyone, and you know a furnace sized by square footage alone can end up wrong for a Colorado winter. You are also aware that an oversized furnace cycles on and off too much, and an undersized one runs constantly and never quite keeps up on the coldest nights.
There's no single BTU number that fits every Colorado house. The right size comes from a heat loss calculation, which weighs your square footage against your insulation, window count, ceiling height, and the altitude and outdoor design temperature for your part of the state. Two homes the same size can need different furnaces if one sits higher up or has more glass facing the weather. A furnace sized too big short cycles, wearing out its parts faster and leaving rooms uneven. One sized too small runs nonstop on the coldest days and still falls behind. Since most homes here heat with gas, getting the size right also means the furnace matches your existing gas line and vent setup rather than just the space it's heating.
Winter nights average 16°F across Colorado, per NOAA climate data, and that's the number a furnace has to be built around, not the mild afternoons. On a night that cold, an undersized furnace just runs and runs, never quite catching up, and you'll notice it in rooms farthest from the furnace staying chilly no matter how long it's been on. An oversized one does the opposite: it blasts the house warm fast, shuts off, then starts again twenty minutes later. Either way you feel it, in cold corners or in a furnace that won't stop clicking on and off. The right size handles a 16°F night without strain and without overshooting, which is why sizing has to start from your coldest nights, not your square footage.
NOAA nClimDiv 1991-2020 county normals weighted by homes
A load calculation is the only way to get this number right, and it takes your house into account the way a square footage chart never can: your insulation, your windows, how the rooms are laid out, and that 16°F design night. Two homes the same size in the same town can need different furnaces once you factor in how much heat they actually lose. Getting the size wrong isn't a small miss either. A furnace that's too big short cycles and wears out early. One that's too small runs constantly and still leaves back bedrooms cold. A local contractor who installs furnaces in Colorado homes all winter has run this calculation enough times to know which assumptions hold up here and which don't, and can tell you the actual number for your house instead of a range pulled from a chart. That's worth having before you buy anything.
A square footage chart assumes every house loses heat the same way, and no two don't. A 1980s house and a 2015 house of the same size can call for different furnace output, because windows, insulation, and ceiling height change how fast heat escapes. Two neighbors with identical floor plans can need different sizes if one has a finished basement adding square footage the furnace also has to cover. That's why a load calculation looks at your specific walls, windows, and layout instead of running your address through a generic table.
Furnaces lose some output at higher elevation because thinner air affects combustion, and much of Colorado sits well above sea level. A furnace rated for sea-level output won't deliver the same heat in Leadville as it would in a Denver basement at a lower elevation. That derating has to get built into the sizing, not added after the fact. It's one more reason a number pulled from a square footage chart, built around sea-level assumptions, can leave a Colorado home under-heated even when the square footage matches what the chart says it should cover.
The right furnace size for your Colorado home comes from a load calculation built around that 16°F design night, not a square footage chart. That's the number worth holding onto. Once you have it, the install matters as much as the math, and that part goes better with someone who already knows the local housing stock, the altitude adjustment your furnace needs, and what tends to go wrong in installs sized off a chart instead of a calculation. A contractor working in your area year-round has seen which BTU output actually holds a Colorado living room at 70 when it's 16 outside, and which falls short. You'll be matched with one licensed contractor local to you, not a handful of companies competing for the job, so the person who calls you is the one who'll size and install the unit, already familiar with what homes like yours need. You came in with a question about a number. You leave knowing the number depends on your house, and who to have check it.
One installer gets your project, so there's no bidding war over it.
You're not committing to anything by asking.